Barricade - Yamaha FZ-16 (2009) - Midnight Black


Thread Starter #646

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
As far as I remember, the last time I swapped the hose, I measured the stock one at 31.5 inches (80cm). I’m guessing the Pulsar hose is 75cm, which is why it’s a tight fit.
So far, the 85cm hose is only available from RCB, but unfortunately, that doesn’t come with rubber grommets. I had a very bad experience buying from Amazon, one seller shipped the wrong size, and the other hasn't shipped yet. Given this, I’m now thinking of buying and importing from AliExpress instead.


View attachment 322076 \
View attachment 322075
Check in local accessory shops too. I have seen many in Cochin and way cheaper than Amazon, around ₹450 (I got from Amazon for ₹599 then). Same generic hoses. Not sure about length. AliExpress won't deliver to India nowadays. Rarely some seller do, but at high shipping rates and will definitely get caught by customs, who'd slap another 60-70% as duty. Not worth unless shipping to some other country and bringing in person by some acquaintance.
 
Joined
Oct 8, 2024
Messages
11
Likes
3
Location
Delhi
Check in local accessory shops too. I have seen many in Cochin and way cheaper than Amazon, around ₹450 (I got from Amazon for ₹599 then). Same generic hoses. Not sure about length. AliExpress won't deliver to India nowadays. Rarely some seller do, but at high shipping rates and will definitely get caught by customs, who'd slap another 60-70% as duty. Not worth unless shipping to some other country and bringing in person by some acquaintance.
Already tried in Karol Bagh, and none of the shops there have the right length. The only exception is Moto Planet, which has RCB hoses for ₹2,399, but those come without rubber grommets.
Regarding the import, the only option I have is to order them to my client’s address, and he’ll ship them to me. But since the shipping cost is quite high (3k via Aramex), I’ll have to order 5-6 hoses to bring down the average cost.
 
Joined
Oct 8, 2024
Messages
11
Likes
3
Location
Delhi
UPDATE

Finally found right length (80 cm) for just Rs 250 in Karol Bagh. Went there to grab a fork rod T and oil seal driver. On the way back, I saw a superbike mod shop and thought, let’s ask one last time. And the guy straightaway told me not to ask anyone else and pointed me to an unnamed shop in a narrow busy street. To my surprise, that little shop had all kinds of hoses.
Most of the hoses they had were DOT certified, but I’m not sure if that’s the real deal or just for the name.

IMG_20241108_161032313.jpg


IMG_20241108_161427166.jpg
 
Thread Starter #649

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
2023 August - Fork Oil Leak

LH fork starts leaking.

2023-08-20 17-18-06.jpg
2023-08-21 18-04-24.jpg


Went to Muthoot Yamaha for parts. Their labour ₹ 280 x 2 + tax. Turnaround time a day or two depending on the rush.

2023-08-21 15-45-07.jpg


Bought the stuff.

2023-08-21 16-35-11.jpg


Fork Oil - Yamalube - 90793-AD803 - ₹ 188.00 x 2
Recommended 10W. 500 ml bottles. Each fork needs 459 ml.

2023-08-21 16-35-51.jpg
2023-08-21 16-35-55.jpg


Fork Dust Seal - 4EB-23144-00 - ₹ 299.00
Bought only one. Only one was damaged, other side replaced not so back.

2023-08-21 16-36-10.jpg


Like always, Ars-HTA brand. Would be some ₹60-70 in their packing.

2023-08-21 16-38-35.JPG


Model 7794.

2023-08-21 16-38-56.JPG
2023-08-21 16-39-04.JPG
2023-08-21 16-39-08.JPG
2023-08-21 16-39-12.JPG


Fork Oil Seal - 2GS-F3145-00 - ₹ 356.00 x 2

2023-08-21 16-36-00.jpg


Again Ars-HTA.

2023-08-21 16-39-36.JPG


Model 7705. Only ₹65 in their packing. Yamaha charging 5.5 times the original rate (so do RE).

2023-08-21 16-39-49.JPG
2023-08-21 16-40-31.JPG
2023-08-21 16-40-36.JPG


Special Washer - 20P-F3418-00 - ₹ 11.00
For steering. Damaged by the previous guy.

2023-08-21 16-41-14.JPG
2023-08-21 16-41-52.JPG


Race Bearing O-Ring - 90202-26142 - ₹ 2.00
Which the previous guy didn't install despite providing new one.

2023-08-21 16-42-17.JPG


Took to KR Motors for fork seal replacement. Didn't have the tools, should get them soon. Youtube mechanics showing crude ways without proper tool, which I never would wanna try.

2023-08-21 18-15-47.jpg


Job done.

2023-08-22 18-15-53.jpg


This is what he is famous for.

2023-08-22 18-16-00.jpg


Perfect job.

2023-08-22 18-24-35.jpg


His best stance.

2023-08-22 18-26-13.jpg
 
Thread Starter #650

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
August 2023 - Misc Updates

Grabrail paint gone the Nth time. Needs rust conversion.

2023-08-28 14-16-39.jpg
2023-08-28 14-22-46.jpg


Stripped the paint.

2023-08-28 14-22-53.jpg


And redid.

2023-08-29 09-58-29.jpg


Ready to install.

2023-09-04 12-39-35.jpg


Oil level alarmingly low. Something is no right. This was after 1.7k km since last oil change.

2023-08-29 10-59-55.jpg


Topped up with Yamalube FS. Took 450 ml to the top of the dipstick.

2023-08-29 10-37-56.jpg


No fouling of the plugs.

2023-08-29 10-44-59.jpg


Not much blowby in the filter box.

2023-08-29 11-17-24.jpg


Atrocities of the old school mech. Replaced the caliper bolts with wrong sized ones with a couple of washers.

2023-09-24 12-52-18.jpg


And abundance of grease everywhere.

2023-09-24 12-52-21.jpg


Bought a pair of bolts from Yamaha.

Flange Bolt - 90105-10319 - ₹ 40.00 x 2

2023-09-28 13-46-08.jpg
2023-09-28 13-46-38.jpg


Original size vs what he had used.

2023-09-28 13-51-46.jpg


New bolts in.

2023-09-28 13-53-36.jpg


Chain nearing its end.

2023-09-28 16-20-20.jpg
 
Last edited:
Thread Starter #651

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
October 2024 - Throttle Cable Replaced

Throttle was hard and getting stuck. Since there are umpteen iterations of cables, have to note down the part number for the correct part.

2023-10-24 14-02-17.jpg


Accelerator Cable - 21C-F6311-10 - ₹ 230.00

2023-10-24 15-00-27.jpg


The ends.

2023-10-24 15-02-22.jpg


Suprajit make.

2023-10-24 15-02-42.jpg


The culprit.

2023-10-24 15-11-05.jpg


Old vs new.

2023-10-24 15-11-56.jpg


Done.

2023-10-24 16-48-21_1.jpg
 
Thread Starter #652

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
November 2023 - Insurance Renewal

Renewed with Acko

Basic Third Party Premium - ₹ 714.00
Own-Damage Premium - ₹ 300.00 (₹ 150.00)
NCB - 50%

Total Premium including GST (18%) - ₹ 1020.00
 
Thread Starter #653

deville_56

Honoured Member
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
November 2023 - (Finally) Engine Rebuild

Something wasn't right ever since the drive axle job (aka the messup) by Royal Yamaha. Tried two places to get things right, but some issue remained. Main issue was, in case of a shut down during cold start idle, bike won't start, needs choke and sometime pushing to get it through. Then, this oil depletion. No burning or leak or blowby, but it's disappearing. Found a new garage, Jixie. An "over educated" enthusiastic guy. He did the rebuild, but wasn't satisfied himself and tore down again to find the root cause. It was a bent decompression cam causing the trouble. New one wasn't available at Yamaha. He sourced a used one. Did the job again. Outcome was great. Normally, FZ would take a good 7-10 feet in 2nd gear for a push start. He demonstrated a jerk start in 1st gear. Settings were that perfect. Gave a demo on the run-in process. Also repaired the starter motor, which was overlooked by many over these years. He used modified Pulsar brushes.

Engine on his bench.

2023-11-26 15-50-03.jpg


He works a single bike a day (or a stretch).

2023-11-26 15-58-42.jpg


Jixie.

2023-11-26 16-16-26.jpg


New cylinder kit.

2023-12-01 10-38-13.jpg


Parts:
Cylinder Kit - ₹ 2,788.00
Timing Chain - ₹ 364.00
Decompression Lever - ₹ 200.00
Exhaust Valve - ₹ 260.00
Gasket Set - ₹ 160.00 x 2
Head O-ring - ₹ 74.00
Valve Stem Seal - ₹ 88.00
Air Filter (Varroc) - ₹ 230.00
Spark Plug (Bosch) - ₹ 130.00
Rocker Arm - ₹ 340.00 x 2
Consumables - ₹ 200.00
Diesel and Petrol (Cleaning) - ₹ 200.00
Petrol - ₹ 200.00
Starter Motor Brush - ₹ 114.00
Sprocket - ₹ 78.00

Labour:
Valve Setting - ₹ 500.00
Engine Parts Water Service - ₹ 100.00
Labour - ₹ 3,000.00

Total - ₹ 9526.00
 
Thread Starter #654
Joined
Sep 11, 2009
Messages
3,026
Likes
4,903
Location
Trivandrum
December 2023 - Misc Updates

When you take alternate routes when you can reach home otherwise in 10 minutes [lol]

2023-12-02 18-12-46.jpg


Visited the spare shop for some Karizma parts and he was sorting FZ parts and saw the wheel hugger. Price was dirt cheap than anticipated. Got one right away. Old one had fading and had striae.

Rear Fender Comp. - 21C-F1650-00 - ₹ 150.00

2023-12-03 15-57-04.jpg

2023-12-03 15-57-00.jpg

2023-12-03 15-59-51.jpg
2023-12-03 15-59-58.jpg
2023-12-03 16-00-04.jpg
2023-12-03 16-00-12.jpg
2023-12-03 16-00-18.jpg


Needed cleanup before install.

2023-12-03 14-49-24.jpg


More than anticipated.

2023-12-03 14-54-38.jpg
2023-12-03 14-54-42.jpg


Took to the nearby wash.

2023-12-03 15-24-38.jpg


Cleaning was thorough,

2023-12-03 15-51-44.jpg


but they missed out the greasy bit. They don't use diesel.

2023-12-03 15-52-25.jpg


New vs old.

2023-12-03 15-58-17.jpg
2023-12-03 15-58-25.jpg


After installation.

2023-12-04 07-34-43.jpg


Spark plug installed by him. Bosch R6. Not a fan of Bosch plugs. The itch starts for the NGK plug.

2023-12-04 07-53-33.jpg


Model UR3DC.

2023-12-04 07-53-29.jpg


Old ebay.in cover used for tool kit.

2023-12-04 07-55-31.jpg


Night at work.

2023-12-04 18-29-49.jpg
 
Top Bottom